BAT-SAFE Professional
$269.00Price
What's included:
- BAT-SAFE Professional charging enclosure
Ships February 2027
top of page
Control workplace battery-fire risk with a repeatable, work-grade charging enclosure.
Rather than relying on improvised charging areas or procedures that vary by shift, BAT-SAFE Professional gives workshops, repair shops, drone operators, fleets, film crews, and schools a defined place to charge up to approx. 1,500 Wh of lithium batteries. If a battery fire occurs, the steel inner vault is designed to contain it while controlled venting manages the release of heat and gases. The repeatable setup also helps reduce liability, downtime, and uncertainty around workplace charging.
An impact-resistant polypropylene outer shell surrounds a powder-coated steel vault. A 30 mm air gap reduces heat transfer, while front and rear one-way vents use metal filter elements to control gas release and stop flame at the exhaust.
Charging leads enter through a dedicated passage in the lid, allowing the box to remain closed and latched during use.
Built for daily professional use
A process that staff can follow and document
Place the batteries inside the steel vault, route the leads through the lid, and secure both latches before charging. The same procedure can be used across shifts, written into charging policies, and shown to insurers, landlords, or fire-safety personnel.
The enclosure holds up to approx. 1,500 Wh in total. That may include several e-bike packs or a larger collection of smaller workplace batteries, provided the combined capacity and physical fit remain within the limits.
1,236 °C inside the vault. 91.5 °C at the outer lid.
In a full-scale instrumented test, approx. 1,500 Wh of LiPo batteries were driven into thermal runaway inside the closed and latched box. The test met all five ADR P911 acceptance criteria.
The report recorded:
An internal peak of 1,236 °C and an outer-lid maximum of 91.5 °C
No external flame
No projectiles
Structural integrity maintained
Controlled venting only
Certification in progress
BAT-SAFE Professional has been internally tested against ADR P911 containment criteria. Formal UN P903/P911 testing at the full approx. 1,500 Wh capacity is underway, and certification hasn’t yet been issued. BAT-SAFE Professional is available for pre-order. Production units will ship after formal testing is complete.
BAT-SAFE Professional is the right size if:
Combined capacity does not exceed approx. 1,500 Wh
Your batteries fit within the 458 × 320 × 200 mm steel vault
There’s room around the batteries for cell expansion
Check both dimensions and watt-hours. The XXL may be enough for a single full-size battery up to 777 Wh; larger workplace loads, several e-bike batteries, or fleets of smaller batteries may require BAT-SAFE Professional.
Which BAT-SAFE do I need?
Model | Internal charging space | Maximum capacity | Typical fit / use |
|---|---|---|---|
BAT-SAFE XS | 165 x 100 x 50 mm / 6.5 x 3.9 x 2.0 in | 50 Wh | Up to two 3S 2200mAh packs; FPV, park flyers, and smaller RC batteries |
BAT-SAFE M | 240 x 165 x 100 mm / 9.4 x 6.5 x 3.9 in | 222 Wh | Up to two 6S 5000mAh packs; everyday RC, heli, and drone charging |
BAT-SAFE XL | 240 x 165 x 380 mm / 9.4 x 6.5 x 15.0 in | 450Wh | Up to four 6S 5000mAh packs; larger RC, heli, drone, and multi-pack setups |
BAT-SAFE XXL E-bike Edition | 240 x 165 x 610 mm / 9.4 x 6.5 x 24.0 in | 777 Wh | One full-size e-bike battery or other long, high-capacity packs |
BAT-SAFE Professional | Steel vault: 458 × 320 × 200 mm | Approx. 1,500 Wh | Several e-bike packs or a larger collection of smaller workplace batteries |
A battery can fit physically and still exceed the Wh rating. Check both before ordering.
Outfitting a workshop, school, or fleet?
Volume pricing is available for multi-unit orders. Contact BAT-SAFE to discuss battery capacity, charging procedures, and the number of enclosures required.
Specifications
Maximum battery capacity | Approx. 1,500 Wh combined |
Typical use | Several e-bike packs or a larger collection of smaller workplace batteries |
Outer dimensions | 24 × 17.7 × 10.6 in / 610 × 450 × 270 mm |
Charging space | 458 x 320 x 200 mm / 18.0 x 12.6 x 7.9 in |
Inner enclosure | Powder-coated steel |
Outer shell | Impact-resistant polypropylene |
Wall construction | Double-wall design with a 30 mm air gap |
Exhaust | Front and rear one-way vents with metal filter elements |
Charging leads | Dedicated wire passage in the lid |
Additional Product Information
BAT-SAFE uses industrial, practical construction for repeated charging and storage. The design prioritizes dependable use over decorative detailing.
Purchase directly from BAT-SAFE or through a distributor listed on BAT-SAFE.com to maintain warranty and ensure you’re receiving the product built to the published specifications.
bottom of page